Jonesboro Electrical Company serves homeowners, businesses, landlords, and property managers across Jonesboro and Clayton County with the full range of residential and commercial electrical work. From a tripped breaker that will not reset to a complete panel upgrade or a new EV charger circuit, the work is covered. When you call, you get straight answers about your panel and wiring before anything is scheduled, so you know what the job involves and what it costs. We are available around the clock, any day of the week. Schedule it. We wire it. You are powered.
Call for a quote: (943) 236-6289
Staying ahead of electrical problems keeps your home safe. A dead outlet, a light that flickers under load, or a breaker that trips every time you run the microwave are all symptoms worth investigating. Each one points to something specific: a loose connection, an overloaded circuit, a failing breaker, or wiring that has reached the end of its useful life. A diagnostic visit covers the symptom and the cause, not just a reset.
Part of that conversation includes GFCI and AFCI protection. GFCI outlets belong in kitchens, bathrooms, garages, and any outdoor location where moisture is a factor. AFCI breakers detect arc faults in the wiring itself, the kind of fault that can start a fire inside a wall before anything trips. Proper grounding and bonding tie into both. If your home was built before these protections became standard, a visit is a good time to assess what is in place and what is not. A breaker that keeps tripping is a warning worth heeding.
Some symptoms should not wait for a convenient appointment window. Call us any time, day or night, if you notice any of the following.
We take calls at any hour, including nights, weekends, and holidays. There is no after-hours surcharge framing here because there are no after-hours. If the problem is happening now, call now.
What sets this service apart is straightforward: a panel that cannot carry your current load is a problem that grows over time, not one that resolves on its own. Older homes in the Jonesboro area were often wired for 100-amp service, which was adequate for the appliance load of that era. A household running central air, an electric range, a washer and dryer, and a home office draws considerably more than that original service was designed to handle. Add an EV charger or a backup generator hookup and the math changes further.
We handle 200-amp service upgrades, subpanel additions, and the load calculations that tell you exactly what the panel needs to support before the work starts. That includes the service entrance and meter coordination where the utility is involved. Electrical work done to the standard the next inspection expects is what we aim for on every panel job, because a panel that passes inspection is a panel that is actually safe. Reach out and we will start at the panel.
Keeping a home safe starts with the wiring behind the walls, and that wiring needs to match what is being asked of it. We install and replace outlets, switches, and dimmers throughout the home, including GFCI outlets in wet locations and AFCI breakers where the code requires them. A dimmer swap, a dead outlet replacement, or a full switch upgrade all fall within a single visit.
Dedicated appliance circuits are a common request. A dryer, an electric range, a washer, or a workshop setup each needs its own circuit sized for the load it draws. Running a 240-volt outlet for a dryer or range is not the same job as adding a standard outlet, and we scope it correctly from the start.
For older homes, whole-home rewiring is sometimes the right answer. Knob-and-tube wiring, aluminum branch circuit wiring, and cloth-sheathed cable all carry risks that a patchwork repair cannot fully address. We assess what is in place and explain what the options are before any work begins. Dead outlets usually have a simple cause worth finding.
Interior and exterior lighting covers a wide range of work, and we handle all of it. Recessed LED lighting is one of the most common residential requests, whether that means retrofitting existing cans or running new circuits for a room that has never had recessed fixtures. Under-cabinet lighting in kitchens, pendant fixtures over islands, and track lighting in commercial spaces all involve the same fundamentals: proper wiring, the right circuit capacity, and fixtures mounted to last.
Ceiling fan installation requires a fan-rated box in the ceiling, the right wiring for a switched or remote-controlled setup, and attention to the load on the circuit. We handle new installations and replacements.
Outdoor and security lighting matters for both residential and commercial properties. Motion-sensor lights, pathway lighting, and floodlights for parking areas and building perimeters all need weatherproof wiring and proper grounding. If you are managing a commercial property in Jonesboro or a rental with exterior lighting that has stopped working, we can scope the repair or the new installation on the call. One call gets the problem looked at properly.
Getting your electrical problem handled starts with a quick call. Whether you own a single-family home in Jonesboro, manage a commercial building in Clayton County, or oversee a portfolio of rental units, the electrical needs are different but the process is the same: call, describe what is happening, get a price, and schedule the work.
For homeowners, that covers everything from a single outlet repair to a full panel upgrade or a whole-home rewiring project. For property managers and landlords, it often means a quick repair between tenants, an electrical safety inspection before a lease, or a pre-purchase inspection that documents what is in place and what needs attention. We treat your home and its wiring the way we would our own, whether it is a primary residence or a rental unit with a problem that needs resolving before the next occupant moves in.
Commercial clients, office buildings, and warehouse spaces have their own demands: dedicated circuits for equipment, panel capacity for expanded operations, and lighting that meets the practical needs of the space. Electrical work here gets handled by people who answer to this community.
Clayton County's four-season climate puts real demand on residential and commercial electrical systems. Summer heat, severe thunderstorms, and the occasional winter ice storm all factor into what properties here need most. The following three services come up regularly for good reason.
Older housing stock throughout the county often carries panels that were sized for a different era. Summer cooling loads, growing appliance demands, and the addition of EV chargers or generator hookups all push older 100-amp services past their limits. A 200-amp upgrade or a subpanel addition gives the home the capacity it actually needs. We run load calculations before the work starts so the upgrade is sized correctly, not just to the minimum.
Georgia storm season brings the kind of weather that takes out power for hours or days at a time. A backup generator connected through a proper transfer switch keeps critical circuits running when the grid goes down. The electrical side of a generator hookup involves the transfer switch, the dedicated circuit from the panel, and the integration that prevents back-feed onto the utility line. We handle the electrical connection and panel work. The generator itself is a separate conversation with the equipment supplier.
Summer lightning activity in Clayton County is significant, and a single nearby strike can send a voltage spike through the service entrance that damages appliances, electronics, and wiring throughout the house. A whole-home surge protector installed at the panel level intercepts that spike before it reaches the branch circuits. It does not replace outlet-level surge strips, but it handles the large transient events that strips are not rated for. If your home does not have panel-level surge protection, it is worth adding.
When you call about a job, you get a price on the call. The scope is confirmed before anything is scheduled, so there is no guessing about what the work involves or what it will cost. If the job requires a site visit to scope accurately, that is explained up front. Ask what it covers and you get a straight answer. Pick up the phone. Get a straight answer. That is how we work.
Call for a quote: (943) 236-6289
We serve Jonesboro and the communities throughout Clayton County and the surrounding region. If you are nearby, we can take the call and get the job on the schedule.
Service area includes: Morrow, Riverdale, Forest Park, Lovejoy, Rex, Hampton, McDonough, and College Park.
Breakers that trip repeatedly without a clear cause, a panel that feels warm or makes buzzing or crackling sounds, breakers that will not reset, and visible corrosion or scorch marks inside the panel are all signs worth taking seriously. Older panels that have been added to over the years without a load assessment may also be running at or past their rated capacity. Call us and we will assess what the panel actually needs.
A burning smell is a sign of heat building up somewhere in the wiring or at a connection point. It can mean a loose connection, an overloaded circuit, or insulation breaking down on older wiring. Do not ignore it and do not keep using the outlet or switch.
Call (943) 236-6289 immediately.
Electrical burning smells are treated as urgent and handled as quickly as the schedule allows.
An inspection makes sense for older homes with an unclear wiring history, properties changing hands, and buildings that have gone through a renovation. It is also useful when a homeowner wants to know what is in place before adding a major load like an EV charger or backup generator. The inspection covers the panel, branch circuits, grounding, outlets, and visible wiring.
We check the breaker ratings against the circuit loads they protect, the condition of the bus bars and connections, whether the panel is properly grounded, and whether the service entrance capacity matches what the home currently demands. If there are double-tapped breakers, signs of overheating, or breakers that are the wrong type for the panel, we identify those as part of the assessment.
Breakers that trip regularly under normal household loads, lights that dim when a large appliance starts, an inability to add circuits without the panel being full, and the addition of a major load like an EV charger or backup generator are all indicators. A 100-amp panel that once served a home adequately may not have the headroom for what a modern household demands. We run a load calculation to confirm what the upgrade needs to cover.
Summer lightning activity in Clayton County is frequent, and a nearby strike can send a voltage spike through the service entrance that reaches every circuit in the house. A panel-mounted surge protector intercepts that spike before it reaches the wiring and connected equipment. It is not a replacement for outlet-level strips, but it handles the large transient events that strips are not rated to absorb.
The electrical side of a generator hookup involves installing a transfer switch at the panel, running the dedicated circuit that connects the generator to the home, and ensuring the installation prevents back-feed onto the utility line. The transfer switch is the critical component. It isolates the generator from the grid during an outage, which protects both the equipment and utility workers on the line. We handle the transfer switch and panel-side work.
When the wiring throughout a home is knob-and-tube, aluminum branch circuit, or cloth-sheathed cable in poor condition, targeted repairs address only the symptom. A whole-home or partial rewire replaces the underlying wiring rather than patching it. We assess what is in place and explain the options clearly before recommending a scope, so you understand what the work involves and why.
GFCI protection is required at outlets in kitchens, bathrooms, garages, and exterior locations. Installing it in an older home that lacks it means replacing the outlets or, in some cases, installing a GFCI breaker that protects the whole circuit. AFCI protection detects arc faults in the wiring itself and is now required in bedrooms and living areas under current code. Both can typically be added without rewiring the entire home, depending on the existing wiring condition.
An outlet or switch that sparks when used, feels warm to the touch, makes a buzzing or crackling sound, or has a cover plate that is discolored are all signs of a problem at the connection. Loose connections at the terminal are a common cause and can create heat over time. These are not cosmetic issues. Call us and we will assess what is happening at the outlet or switch and what the repair involves.
Flickering or dimming lights can point to a loose connection at the fixture, a failing breaker, a circuit that is overloaded, or a problem at the service entrance. If flickering happens throughout the house rather than on a single circuit, the issue is more likely at the panel or service entrance level. We trace the symptom to the source before recommending a repair.
A targeted repair is appropriate when the fault is isolated, the surrounding wiring is in good condition, and the fix brings the affected area up to current standards. When the wiring throughout a section of the home is degraded, undersized, or the wrong type for the load, a patch does not address the underlying problem. We tell you which situation you are dealing with before the work begins.
The affected circuit is de-energized before any outlet, switch, or fixture work begins. For panel work or service upgrades, the main power is off for part of the visit. We explain exactly what will be shut down and for how long before the work starts, so you can plan around it.
Jonesboro Electrical Company handles repairs, panel upgrades, new wiring, lighting, EV charger circuits, generator hookups, surge protection, and every other residential and commercial electrical job in between. We are available at any hour, any day of the year. Schedule it. We wire it. You are powered.
Call for a quote: (943) 236-6289
Every electrical job we take on in Jonesboro starts the same way: you call, describe what is happening, and we give you a straight answer about what the work involves and what it will cost before anything is scheduled. The table below covers the services we handle most often for homeowners, businesses, landlords, and property managers across Clayton County. Use it to find what fits your situation, then call and we will scope the job from there.
| Service | What the Job Involves | Common Situations | What to Keep in Mind |
|---|---|---|---|
| Electrical Repairs and Troubleshooting | Dead outlets and switches, Flickering or dimming lights, Circuit faults traced to the source, Loose connections and failing components | Any home or business with a symptom that needs a cause, not just a reset | A diagnostic visit covers the root cause, not just the visible symptom. Tracing the fault before replacing parts saves time and avoids repeat calls. |
| Backup Generator Installation | Transfer switch installation at the panel, Dedicated generator circuit, Back-feed prevention wiring, Panel integration for critical circuits | Clayton County homeowners who want power for critical circuits when Georgia storms take out the grid | The transfer switch is the critical component. It isolates the home from the utility line during an outage, protecting both the equipment and anyone working on the line outside. We handle the electrical side. The generator unit itself is sourced separately. |
| Dedicated Appliance Circuits | 240-volt circuits for dryers and ranges, Circuits for washers and refrigerators, Workshop and garage circuits, Properly sized breakers for each load | Homeowners adding a major appliance or a workshop that needs its own circuit rather than sharing one | A dryer or electric range needs a 240-volt circuit sized for its draw. Running one is not the same job as adding a standard outlet, and we scope it correctly from the start. |
| Electrical Panel and Service Upgrades | 200-amp service upgrades, Subpanel additions, Load calculations before the work starts, Service entrance and meter coordination | Homes with older 100-amp panels, properties adding major loads like EV chargers or generators, and buildings expanding operations | A panel upgrade in Clayton County typically involves a permit and inspection. We handle the scope and load calculation up front so the upgrade is sized for what the home actually needs, not just the minimum. |
| Outlet and Switch Installation | GFCI outlet installation, Standard and USB outlet replacement, Dimmer and smart switch upgrades, AFCI breaker installation | Homeowners adding outlets, updating older devices, or bringing wet-location protection up to code | GFCI protection is required at kitchens, bathrooms, garages, and exterior locations. Older homes that lack it can usually be brought up to standard without a full rewire. |
| Electrical Safety Inspections | Panel and branch circuit assessment, Grounding and bonding check, Outlet and wiring condition review, Documentation of findings | Older homes, properties changing hands, landlords preparing a unit, and homeowners adding a major new load | An inspection before adding an EV charger or generator hookup tells you whether the panel has the capacity or whether an upgrade needs to come first. We document what we find so you have a clear picture before any work is committed. |
| Lighting Installation | Recessed LED retrofits and new runs, Exterior and security lighting, Under-cabinet and accent lighting, Commercial fixture and track lighting | Residential and commercial properties adding, replacing, or upgrading interior or exterior lighting | New recessed lighting in a room that has never had it requires running circuits, not just swapping fixtures. We scope what the ceiling and panel can support before the work starts. |
| Breaker and Fuse Repair | Breakers that trip repeatedly, Breakers that will not reset, Fuse panel assessment, Faulty breaker replacement | Homes and businesses where a breaker is misbehaving or a fuse panel is overdue for attention | A breaker that trips under normal load is pointing at something. We find out whether the issue is the breaker itself, the circuit, or the load before recommending a fix. |
| Older-Home Rewiring | Knob-and-tube wiring replacement, Aluminum branch circuit assessment and remediation, Cloth-sheathed cable replacement, Whole-home or partial rewire scoping | Owners of older Jonesboro homes where the wiring type or condition makes targeted repairs insufficient | Knob-and-tube and aluminum branch circuit wiring carry risks that a patch cannot fully address. We assess what is in place and explain the options before recommending a scope, so the decision is based on what is actually there. |
| Whole-Home Surge Protection | Panel-mounted surge protector installation, Protection against lightning-induced spikes, Coordination with outlet-level strip protection, Assessment of existing surge protection | Jonesboro and Clayton County homes exposed to frequent summer lightning activity | A panel-level surge protector handles the large transient events that outlet strips are not rated to absorb. One nearby lightning strike can reach every circuit in the house through the service entrance. |
| Ceiling Fan Installation | Fan-rated box installation, New wiring for switched or remote setups, Replacement of existing fans, Load check on the circuit | Homeowners adding or replacing ceiling fans, especially where no fan box currently exists | A ceiling fan requires a fan-rated box rated for the weight and motion. A standard light fixture box is not rated for it, and we confirm the right box is in place before the fan goes up. |
| Wiring and Circuit Installation | New circuit runs throughout the home, Rewiring for renovations and additions, Circuit capacity for expanded loads, Wiring to current code standards | Homeowners finishing a basement, adding a room, or expanding a commercial space that needs new circuits | Wiring for an addition has to match the panel capacity and the code in effect at the time of the permit. We confirm both before the first wire is pulled. |
What causes a breaker to trip repeatedly, and when does it mean something more serious?
A breaker trips when the current on a circuit exceeds what the breaker is rated for. That can mean the circuit is overloaded by too many devices, a single appliance is drawing more than expected, or there is a fault somewhere in the wiring. A breaker that trips repeatedly under normal household use is not a nuisance, it is a signal. If resetting it brings it back only to trip again, the underlying cause needs to be found before the breaker is replaced or the circuit is extended. We trace the fault to the source rather than starting with a replacement.
How do I know if my home's wiring is safe, especially in an older house?
Older homes in the Jonesboro area were built in eras when wiring standards, materials, and load expectations were very different from what modern households require. Knob-and-tube wiring, aluminum branch circuit wiring, and cloth-sheathed cable all have characteristics that make them worth assessing before adding load or assuming the home is ready for modern demands. An electrical safety inspection covers what type of wiring is in place, its condition, whether the grounding and bonding are adequate, and whether the panel matches what the home is asking of it. That gives you a factual picture rather than a guess.
What does an EV charger installation actually involve on the electrical side?
A Level 2 EV charger runs on a 240-volt dedicated circuit, typically a 50-amp circuit for most home charging setups. That means running new wiring from the panel to the charger location, installing the right outlet or hardwired connection, and confirming the panel has the capacity to carry the added load. If the panel is already close to its limit, a service upgrade may need to come first. We assess the panel before the circuit is run so the installation is sized for what the vehicle and the home actually need.
Faults Traced Before Anything Is Replaced
We find the cause before recommending a fix. Replacing a breaker or an outlet without understanding why it failed means the same problem comes back. A diagnostic visit covers the symptom and the source.
How long does a panel upgrade or service upgrade typically take?
A straightforward 200-amp service upgrade is usually a full-day job. The scope includes the new panel, the service entrance work, coordination with the utility where the meter is involved, and the inspection that follows. Homes that need additional work, such as a subpanel, new grounding, or circuit reorganization, take longer. We confirm the scope and the timeline on the call before anything is scheduled so you know what the day involves.
Is electrical work in Jonesboro permitted and inspected?
Panel upgrades, new circuit runs, service entrance work, and other significant electrical jobs require a permit in most jurisdictions, and Clayton County is no exception for the jobs that fall under that requirement. Permitted work is inspected, which means the installation is reviewed against the code in effect at the time. We handle the permit process where it applies and schedule the work so the inspection fits the timeline. Electrical work done to the standard the next inspection expects is what we aim for on every job.
When should I call an electrician rather than attempting a repair myself?
Swapping a light bulb or resetting a tripped breaker is straightforward. Anything that involves opening an outlet, switch, or fixture, touching wiring, working inside the panel, or adding a circuit is a different matter. The panel in particular carries live voltage at the service entrance even when the main breaker is off. Wiring mistakes in walls can create faults that are not immediately visible but become hazards over time. If you are not certain what you are dealing with, a call costs nothing and gives you a straight answer about what the job actually involves.
Code-Compliant Work on Every Job
Every job we take on is done to the standard the next inspection expects. That applies to a single outlet replacement and a full service upgrade alike.
What is involved in grounding and bonding, and why does it matter in an older home?
Grounding provides a safe path for fault current to return to the source, which allows breakers to trip when something goes wrong rather than letting the fault persist. Bonding connects metal components throughout the home so they stay at the same electrical potential, which prevents a shock hazard when someone touches two metal surfaces at once. Older homes were sometimes wired without a ground wire in the branch circuits, or with grounding that does not meet current standards. An inspection covers both and tells you what is in place and what would bring it up to current expectations.
How do we handle emergency electrical calls in Jonesboro?
We take calls at any hour, any day of the week, including nights, weekends, and holidays. There is no separate after-hours line and no time when the phone is not answered. If you are dealing with a burning smell, a sparking outlet, a panel making noise, or a fault that has taken out part of the house, call us now. We will ask the right questions on the call to understand what is happening and get the job on the schedule.
Scope Agreed Before the Panel Is Opened
You get a clear picture of what the work involves and what it costs before anything starts. If the job needs a site visit to scope accurately, we tell you that on the call.
What is the risk of aluminum branch circuit wiring in an older home?
Aluminum branch circuit wiring was used in residential construction during a period when copper prices were high. The material expands and contracts differently than copper, which can loosen connections at outlets, switches, and fixtures over time. Loose connections create heat, and heat at a connection point is a fire risk. Homes with aluminum branch circuit wiring are not automatically unsafe, but they benefit from an assessment that confirms the connections are properly made with compatible devices. We look at what is in place and explain the options clearly.
What should I know about adding circuits for a workshop or garage?
A workshop or garage with power tools, compressors, or welding equipment draws significantly more than a standard household circuit is sized for. Each major tool or piece of equipment typically needs its own dedicated circuit sized for its rated draw. That means running new circuits from the panel, confirming the panel has the capacity, and installing the right outlets for each load. If the panel is already full or close to its limit, a subpanel in the garage is often the right answer. We scope the whole picture before the first circuit is run.
Is a home ready for a backup generator or EV charger without a panel upgrade?
It depends on what the panel is rated for and what it is already carrying. A 100-amp panel in a home with central air, a washer and dryer, and an electric range may have very little headroom left. Adding a generator transfer switch or an EV charger circuit on top of that load can push the service past its rated capacity. A load calculation tells you exactly where the panel stands before any work is committed. If an upgrade is needed, we scope that first so the generator or charger installation goes in correctly.
Call (943) 236-6289 and we will walk through what your electrical job involves, give you a price, and get it on the schedule.
(943) 236-6289